Skip to main content
Hsdian Construction Machinery - North America

Home / Why 40 Ton Load Is Applied In Aggregate Crushing Test

Why 40 Ton Load Is Applied In Aggregate Crushing Test

Hot Products

Aggregate crushing value test | Step by Step Procedure ...

Now, 40 tons of load is applied to the test cylinder in 10 minutes. We know, 40 ton= 40000 kg= 400 KN. Therefore, 400 KN of the load should be applied. The time(10 minutes) is started in the stopwatch. The crushed material is then transferred into the sieve of size 2.36 mm.

Read More

Aggregate Crushing Value Test - Procedure And Result ...

The aggregate sample is filled in a cylindrical mold and a load of 40 ton is applied through a plunger in a compression testing machine. The crushed aggregate sample which is finer than 2.36 mm is separated and expressed as a percentage of the original weight taken in the mould.

Read More

Why 40 Ton Load Is Applied In Aggregate Crushing Test

Why 40 Ton Load Is Applied In Aggregate Crushing Test 28 Days Crushing Load Test-India Crusher&Mill ... crushing load test; ... test) load is applied at a constant rate of stress cube undergoing comression loading test at the . difference between aggregate impact ...

Read More

Aggregate Crushing Value Calculator, Test on course and ...

The aggregate crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. To achieve a high quality of pavement, aggregates possessing low aggregate crushing value should be preferred. ... Why to test Aggregate Crushing Value? ... The total load shall be 40 tonnes.

Read More

Aggregate Crushing Value Test - L & T - Learning Technology

Step-9 : Apply the load at a uniform rate of 40 kilo Newton per minute until the total applied load is 400 Kilo Newton. Step-10 : Release the load and take the crushed aggregate out of the mould. Step-11 : Sieve the crushed aggregate through 2.36 mm IS sieve and weigh the fraction passing through it to an accuracy of 0.1 gram.

Read More

Aggregate Crushing Value Test - Vidyarthiplus

Aggregate Crushing Value Test INTRODUCTION ... Compressions testing machine capable of applying load of 40 tonn£s, at a uniform rate of loading ... with the plunger in position is placed in the compression testing machine. The load is applied at a uniform

Read More

How to Determine the Aggregate Crushing Strength Value in ...

The load is applied to the plunger at a uniform rate of 4 tonnes per minute.Wait for 10 minutes and the total load applied to the aggregates will be 40 tonnes. After applying the load, the crushed aggregates are taken and then passed through 2.36mm sieve.Take the weight of crushed aggregates passing through 2.36 mm sieve.Let the weight of ...

Read More

CIVIL QUALITY CONTROL LAB: AGGREGATE CRUSHING VALUE

Load is then applied through the plunger at a uniform rate of 4 tonnes per minute until the total load is 40 tonnes, and then the load is released. Aggregates including the crushed portion are removed from the cylinder and sieved on a 2.36mm IS sieve.

Read More

Aggregate Crushing Value Test -Determine Aggregate ...

Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to a specified load under standardized conditions.

Read More

Aggregate Tests | SpringerLink

Crushing test – provides an indication of aggregate resistance to crushing under an applied crushing load. The test requires samples of the aggregate to be subjected to standard load crushing conditions. Multiple layers of presieved materials are tamped 25 times before a 40-ton load is applied

Read More

Lab Test on Aggregates at Site - CivilJungle

To calculate aggregate Crushing value by testing aggregate passing 12.5 mm sieve and retained on a 10 mm sieve. ... The load shall be applied at a uniform rate so that the load of 40T is reached in 10 minutes. ... IS Sieves 40 mm, 20 mm, 16 mm, 12.5 mm, 10mm, and pan ...

Read More

what is aggregate crushing test - Agri Alliance

The aggregate crushing value (ACV) of an aggregate is the mass of material, expressed as a percentage of the test sample. which is crushed finer than a 2,36 mm sieve when a sample of aggregate passing the 13,2 mm and retained on the 9,50 mm sieve is subjected to crushing under a gradually applied compressive load of 400 kN. 2 APPARATUS

Read More

Pavement materials: Aggregates

The specimen is subjected to a compressive load of 40 tonnes gradually applied at the rate of 4 tonnes per minute. Then crushed aggregates are then sieved through 2.36 mm sieve and weight of passing material is expressed as percentage of the weight of the total sample which is the aggregate crushing

Read More

Aggregate crushing strength test - SlideShare

Dec 30, 2018 · After Sieving dry the test specimens by heating at a temperature of 105±5oC. 9 (Table:03) Guide to minimum mass of test portions required to obtain a suitable mass of material to determine the aggregate crushing value Grading of the aggregate Minimum Mass of the test portion1) mm All-in aggregate 40 max. size All-in aggregate 20 max. size ...

Read More

7 LAB TESTS ON AGGREGATE TO CHECK QUALITY FOR USE IN

Sep 12, 2015 · The specimen is subjected to a compressive load of 40 tonnes gradually applied at the rate of 4 tonnes per minute. Then crushed aggregates are then sieved through 2.36 mm sieve and weight of passing material ( W2 ) is expressed as percentage of the weight of the total sample ( W1 ) which is the aggregate crushing value.

Read More

7 Lab Test on Aggregate Should Satisfy for Use in Concrete

The aggregate crushing value test indicates the strength of aggregate which is the most essential property of coarse aggregate. The aggregate crushing value provides a relative measure of resistance to crushing under a gradually applied compressive load. For achieving a high quality of pavement, aggregate of higher crushing strength i.e. low ...

Read More

Compressive Strength of Concrete | Cube Test, Procedure ...

May 18, 2018 · The test is carried out using 150mm concrete cubes on a Universal testing machine or compressive testing machine. Apparatus. As per IS: 516-1959 Compressive testing machine (2000Kn),15cm×15cm×15cm steel cube molds or Cylinder having Dia 15cm and length 30cm are used. The test includes following steps:-Preparing of material for Cube test:

Read More

IS 2386-4 (1963): Methods of test for aggregates for ...

2.1 Object - This method of test covers the procedure for determining aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre-

Read More

Various Lab Test On Aggregates - Civil Engineering

Aggregate Crushing Value ... 40 am. it is adequate to conduct the relevant test on aggregate,before it use. Reply Link. achuthan September 5, 2011 at 12:58 am. hi, please give me the details of testing the aggregates in quarry and also the important tests,&test procedure with required equipment’s.

Read More

Aggregate Crushing Value test – we civil engineers

Jan 23, 2018 · AIM: To determine the aggregate crushing value of coarse aggregates as per IS: 2386 (Part IV) - 1963. APPARATUS: i) Cylindrical measure and plunger ii) Compression testing machine iii) IS Sieves of sizes - 12.5mm, 10mm and 2.36mm PROCEDURE: i) The aggregates passing through 12.5mm and retained on 10mm IS Sieve are oven-dried at a

Read More

Compressive Strength Test Of Concrete - Detailed Guide

The specimen should be weighed before the test. The specimen should be placed between the plate with proper alignment. Now, apply the load (kilonewton) gradually to the specimen. The specimen will break at maximum load (1 Division = 5 KN), which is noted down as the crushing value of the cube.

Read More

Discussion of experiment aggregate crushing value test ...

A compression testing machine capable of applying load up to 40 tonnes at a uniform rate of 4 tonnes per minute. A cylindrical measure having internal diameter 11.5cm and height 18cm. THEORY The “aggregate crushing value” give a relative measure of the resistance of an aggregate to crushing under agradualy applied compressive load.

Read More

How to Find Aggregate Crushing Value and Its Test Procedure?

The aggregate crushing value provides a relative measure of the resistance of an aggregate to crushing under gradually applied crushing load. The aggregate crushing value test is a useful guide when dealing with aggregates of unknown performance, particularly when lower strength is suspected.

Read More

Aggregate crushing strength test - SlideShare

Dec 30, 2018 · After Sieving dry the test specimens by heating at a temperature of 105±5oC. 9 (Table:03) Guide to minimum mass of test portions required to obtain a suitable mass of material to determine the aggregate crushing value Grading of the aggregate Minimum Mass of the test portion1) mm All-in aggregate 40 max. size All-in aggregate 20 max. size ...

Read More

Discussion of experiment aggregate crushing value test ...

A compression testing machine capable of applying load up to 40 tonnes at a uniform rate of 4 tonnes per minute. A cylindrical measure having internal diameter 11.5cm and height 18cm. THEORY The “aggregate crushing value” give a relative measure of the resistance of an aggregate to crushing under agradualy applied compressive load.

Read More

IS 2386-4 (1963): Methods of test for aggregates for ...

2.1 Object - This method of test covers the procedure for determining aggregate crushing value of coarse aggregate. NOTE 1 -The ‘aggregate crushing value’ gives a relative measure of the resistance of an aggregate to crushing under a gradually applied compressive load. With aggre-

Read More

Aggregate - coarse aggregates, testing & limits

Sep 05, 2018 · AGGREGATE CRUSHING VALUE • I.S. 2386-PART 4 • Aggregate crushing value test on coarse aggregates gives a relative measure of the resistance of an aggregate crushing under gradually applied compressive load. • Coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected to ...

Read More

Compressive Strength of Concrete Cubes - Lab Test & Procedure

The load will be applied to the specimen axially. Now slowly apply the load at the rate of 140kg/cm 2 per minute till the cube collapse. The maximum load at which the specimen breaks is taken as a compressive load. Calculation. Compressive Strength of concrete = Maximum compressive load /

Read More

concrete – Construction Civil Concepts In my Pocket

Compressive Strength Test . Maximum construction site have the cube testing machine of capacity 100 ton/ 1000 KN. We calculate the compressive strength as Load / Area i.e. N/mm². If we increase the loading area, the load for crushing or the load at which it fails also increases.

Read More

Influence of crushing index on properties of recycled ...

Mar 15, 2017 · 2.3. Testing methods. The crushing index was determined in accordance with Pebble and crushed stone for construction (GB/T14685-2011) . Firstly, 3000 g of sample (M 1) was put into the determinator under pressure testing. Then test machine was started by the velocity of 1 kN per second until the load of 200 kN.

Read More

Stabilizer for aggregate trails, pathways, and patios

depth. To achieve saturation of Stabilized aggregate profile, 25 to 45-gallons of water per 1-ton must be applied. During water application, test moisture penetration using a probing device reaching full depth. Better to over water than under water

Read More

Compressive Strength of Concrete | Cube Test, Procedure ...

May 18, 2018 · The test is carried out using 150mm concrete cubes on a Universal testing machine or compressive testing machine. Apparatus. As per IS: 516-1959 Compressive testing machine (2000Kn),15cm×15cm×15cm steel cube molds or Cylinder having Dia 15cm and length 30cm are used. The test includes following steps:-Preparing of material for Cube test:

Read More

Various Lab Test On Aggregates - Civil Engineering

Aggregate Crushing Value ... 40 am. it is adequate to conduct the relevant test on aggregate,before it use. Reply Link. achuthan September 5, 2011 at 12:58 am. hi, please give me the details of testing the aggregates in quarry and also the important tests,&test procedure with required equipment’s.

Read More

Determination of Aggregate Impact Value - Impact Test on ...

The aggregate impact value is a measure of resistance to sudden impact or shock, which may differ from its resistance to gradually applied compressive load. Procedure of Aggregate Impact Test. The test sample consists of aggregates sized 10.0 mm 12.5 mm. Aggregates may be dried by heating at 100-110° C for a period of 4 hours and cooled.

Read More

Experimental Study on usage of Class-E Glass Fiber in the ...

Experimental Study on usage of Class-E Glass Fiber in the Cement Concrete P. Arulsivanantham Lecturer, Department of Civil Engineering, Ambo University, Ambo – 19, Ethiopia.

Read More

Performance evaluation of hot mix asphalt containing ...

Aug 29, 2020 · The load was applied for 100 milisec (0.1 sec) and rest period was kept 900 ms (0.9 sec). The test was performed at 40 °C and continued for 10,000 cycles or up to the 10,000 micro strains, whichever occurred first. Download : Download high-res image (112KB) Download : Download full-size image; Fig. 4. Dynamic creep test set up.

Read More

Laboratory Testing - Statens vegvesen

2.6 Aggregate Crushing Value (ACV) BS812:Part 110:1990 2.7 Ten Percent Fines Value (TFV) BS812:Part 111:1990 2.8 Aggregate Impact Value (AIV) BS812:Part 112:1990 2.9 Los Angeles Abrasion Test (LAA) ASTM C535-89 2.10 Sodium Soundness Test (SSS) ASTM C88-90 2.11 Slump Test BS1881:Part 102:1983 2.12 Making of Concrete Test Cubes BS1881:Part 108:1983

Read More